FAQs

Should I tuck the balaclava into the shirt or flash suit to meet OSHA 1910.260 or NFPA 70E?

Should I tuck the balaclava into the shirt or flash suit to meet OSHA 1910.260 or NFPA 70E?

Although no standard specifically covers it, Oberon recommends tucking the balaclava in to prevent a possible arc from coming up underneath the flap of the balaclava.


How do I clean and disinfect my Oberon face shield?

How do I clean and disinfect my Oberon face shield?

To clean and disinfect an Oberon face shield it is best to use a damp, soft cloth and gently wipe away any dirt or grit.  Once this is done gently flush them off with room temperature tap water. To disinfect a FaceFit™ shield clean first and then dampen a soft cloth with isopropyl alcohol or use a Lysol® wipe. This process may leave streaks as the surface dries. Once dry, use a...


How do I clean and disinfect safety googles and spectacles?

How do I clean and disinfect safety googles and spectacles?

To clean and disinfect Oberon safety goggles and spectacles it is best to use a damp, soft cloth and gently wipe away any dirt or grit.  Once this is done gently flush them off with room temperature tap water. Once the safety goggles or spectacles are cleaned it is also important to disinfect them. Take a soft cloth that has been dampened with isopropyl alcohol or use a Lysol® wipe and gently...


How do I clean the inside of my arc flash hood?

How do I clean the inside of my arc flash hood?

The first step to cleaning and disinfecting an Oberon TCG™ hood is to disassemble your hood.  Once done, if the shield has dirt or grit, flush it off with room temperature tap water. The next step to disinfecting a TCG™ hood window is to take a soft cloth with isopropyl alcohol or use a Lysol® wipe and gently clean both sides of the shield. This process may leave streaks as...


How do I select the appropriate Arc Flash PPE according to NFPA 70E or CSA Z462?

How do I select the appropriate Arc Flash PPE according to NFPA 70E or CSA Z462?

According to NFPA 70E Standards for Electrical Safety in the Workplace there are two potential methods for determining arc flash PPE. The incident energy analysis method in accordance with table 130.5(G) The arc flash PPE category method in accordance with table 130.7(C)(15) Depending on which method is used the tables in NFPA 70E can help you identify what arc flash PPE is required.  Table 130.7(C)(15)...


If NFPA 70E and CSA Z462 require a hood be worn when the incident energy level is above 12 cal/cm2 why does Oberon Company sell a 25 cal/cm2 hard cap and shield combo with a balaclava?

If NFPA 70E and CSA Z462 require a hood be worn when the incident energy level is above 12 cal/cm2 why does Oberon Company sell a 25 cal/cm2 hard cap and shield combo with a balaclava?

  There are many standards involved when dealing with electrical safety in the workplace.  NFPA 70E and CSA Z462 both help to lay the groundwork for companies to create electrical safety programs that protect the welfare and safety of their workers.  While these standards are a...


Does the Oberon TCG™ Series shield block Infrared light? I am worried my eyes might be damaged if I am hit with and arc flash.

Does the Oberon TCG™ Series shield block Infrared light?

When you are involved in an arc flash two things occur simultaneously and help prevent damage to your eyes. You blink.  This happens very quickly.  A good example of this at work would be when you accidentally look at the sun.  Your first reaction is to immediately close your eyes. The blinding flash of an arc lasts as long as the arc flash is present. This would be about one third of a second...


How long does the user have to put new gloves into service?

How long does the user have to put new gloves into service?

The user has 12 months from the test date to put new gloves into service. It is important to note that the user must document when the gloves are put into service to comply with OSHA 1910.137 guidelines.


How are Oberon electrical gloves tested?

How are Oberon electrical gloves tested?

The manufacturer of Oberon gloves electrically tests every glove prior to shipment. Each “batch” of gloves is also subjected to a battery of physical and electrical tests to insure that the gloves meet the D120 Standards. It is the responsibility of the employer to insure that the gloves have passed the required electrical test within the specified time.


What size leather protector should I use?

What size leather protector should I use?

Leather protectors should always be worn with rubber insulating gloves. ASTM F696 provides the specification for the manufacture of Leather Protectors. Leather protectors are sized to be worn on the same size rubber insulating glove so if you wear a size 10 rubber insulating glove you should order a size 10 leather protector.